These are all list of error code in Canon iR/iR more to come, i hope your machines works fine and never get error. E Main cause. fixing oil, the error code is indicated. E The rated voltage of the power supply and that of the fixing unit do not match. E Clock pulses fail to be generated. canon ir is showing an error codes E How it will solve? Your error code is for the fixing unit solve by checking the follwoing: 1. Fixing lamp.
|Published (Last):||18 September 2014|
|PDF File Size:||14.9 Mb|
|ePub File Size:||13.38 Mb|
|Price:||Free* [*Free Regsitration Required]|
The laser driver PCB isfaulty. The SSR has a short circuit. The wiring is faulty short circuit, opencircuit. The finisher controller PCB isfaulty. Main cause The LAN ur6000 is faulty. The stitch motor front, M7S is faulty. Mode ofDetection The guide home position sensor does not turn on when the guidemotor has been driven for about 0.
Canon iR5000 Service Manual: Error Codes; List Of Error Codes
The delivery door switch MS3S is faulty. Mode ofDetection The puncher does not leave home position when the punch motorhas been driven for msecs.
The delivery motor M2 is faulty. After replacing the fixing web, be sure to reset the two web counters coce service mode: The copy data controller orthe remote diagnostic device is faulty. About me indra Indonesia Just want to share View my complete profile.
Main Cause The hard disk fan FM7 is faulty. The hopper connector is left disconnected. The paperpush-on plate home position sensor PI14S is faulty.
Mode ofDetection Communication between the height sensor and the finisher controllerPCB is not possible, or communication data has an error. The front door switch MS2S erorr.
Main Cause The tray home position sensor PI8 is faulty. The wiring is faulty short circuit,open circuit. The laser scanner motor M15 is faulty.
Error Codes > Canon > iR > page 2
Caution No code is indicated, and keys are locked. Mode of Detection The stitcher home position sensor rear does not turn off when thestitch motor rear has been rotated CW for 0. Mode ofDetection The alignment plate does not leave home position when the alignmentmotor has been driven for 2 secs.
The sub thermistor TH2 has detected overheating. The reader controller PCB isfaulty.
The tray upper cods detecting switch MS5 is faulty. Mode ofDetection The copy data controller or the NE controller is out of order or anopen circuit has been detected. Main Cause The shutter open sensor PI5 is faulty. Mode cde The shutter closed detecting switch does not turn on when the No.
Main Cause The stapler home position detecting switch MS7 is faulty. The heat discharge fan FM3 is faulty. The guide motor M3S is faulty. Crazy About Copiers Loading The DC power coce fan FM6 is faulty. The puncherdriver PCB is faulty. The remote diagnostic device PCBis faulty. The lamp inverter PCB is faulty. The swing motor M7 is faulty. Main Cause The stapler shift home position sensor PI7 is faulty. Main Cause The various printer board accessories are faulty. Mode ofDetection The stapler unit does not leave home position when the stapler shiftmotor has been driven for 4 secs.
Main Cause The cooling fan FM1 is faulty. The coin vendor is faulty. Mode ofDetection The paper push-on plate home position sensor does not turn onwhen the paper push-on plate motor has been driven for 0. The SSR is faulty. The fixing motor Ocde is faulty.
The primary charging assemblycooling fan FM2 is faulty. Mode of Detection When the inlet cover, front cover, and the delivery cover are foundto be closed, the inlet door switch detects an open condition for 1sec or more from the start of the initial rotation of the host machineor the start of printing.
Mode ofDetection The alignment plate home position sensor does not turn on whenthe alignment motor has been driven for 0.